Search found 12 matches

by rfcom
Fri Jun 29, 2012 10:08 am
Forum: Vertex
Topic: VX-4207 Ignition Sense
Replies: 1
Views: 2026

Re: VX-4207 Ignition Sense

In the software, under Common and DSUB-15, your ACC I/O Port 1 Input is programmed for Ignition. change it to none (or any other option) and you will not need to have 12V on this input to power up the radio.
by rfcom
Sun Sep 05, 2010 10:00 am
Forum: Vertex
Topic: VXR-9000U Reference Freq Adjust
Replies: 8
Views: 4407

Re: VXR-9000U Reference Freq Adjust

VERTEX intentionnaly omitted to install some componants on the RF board and this is why frequency can`t be tuned on the VXR-9000 V and U.
by rfcom
Sun Sep 05, 2010 9:50 am
Forum: Vertex
Topic: Vertex 3000
Replies: 2
Views: 2654

Re: Vertex 3000

Have you tried it with mic on hook ?
by rfcom
Fri Jun 12, 2009 10:08 am
Forum: Vertex
Topic: Programming VX-160
Replies: 3
Views: 3598

Re: Programming VX-160

Usually the problem comes from the USB to serial converter built into the cable wich is not 100% reliable. Using a serial interface cable on a computer wich does have a serial com port or using the VERTEX FIF-10 USB interface cable would work fine. You could also try to checkmark the FIF-10 field un...
by rfcom
Fri Jun 12, 2009 9:54 am
Forum: Vertex
Topic: interfacing controller to VXR-9000u
Replies: 4
Views: 1562

Re: interfacing controller to VXR-9000u

I am pretty sure (but not 100%) it will. You will have to put a checkmark in the "Req" field if you don`t want it to send the ID when the transmitter is not activated for a time exeeding the one programmed in the "Int T" field.
by rfcom
Thu Jun 11, 2009 12:02 pm
Forum: Vertex
Topic: Need help programing Vertex 180
Replies: 1
Views: 1095

Re: Need help programing Vertex 180

Under file/configure, try the differents com ports available.
by rfcom
Thu Jun 11, 2009 11:58 am
Forum: Vertex
Topic: interfacing controller to VXR-9000u
Replies: 4
Views: 1562

Re: interfacing controller to VXR-9000u

The VXR-9000 could be programmed for base or repeat mode but you will need to program one of the function key for remote toggle. Once this key is pressed, the internal controller is disabled and the VXR-9000 is controlled by anything hooked to the accessory connector . You should also program the st...
by rfcom
Mon Mar 30, 2009 9:26 am
Forum: Vertex
Topic: VX-2200 programming
Replies: 2
Views: 1473

Re: VX-2200 programming

Click on Channel (on the top of the main screen) then on Channel Allocations/Group Alpha Tag to create the other groups needed. These new groups will then become available in the group field of the main screen. The radio should not go into dual watch mode unless you press on a key already programmed...
by rfcom
Thu Mar 19, 2009 10:04 am
Forum: Vertex
Topic: VX-924 "Channel Step Mismatch" error while programming
Replies: 6
Views: 2358

Re: VX-924 "Channel Step Mismatch" error while programming

Even if you get the "alignment data not defect" message, you should accept to restore to the factory default. Very often, the software does not see that there is corrupted data. There are no issues when the ce59 is used with the differents operating systems but I saw some issues when used with speci...
by rfcom
Mon Mar 16, 2009 1:35 pm
Forum: Vertex
Topic: VX-924 "Channel Step Mismatch" error while programming
Replies: 6
Views: 2358

Re: VX-924 "Channel Step Mismatch" error while programming

It looks like the radio still got corrupted data (PLL reference frequency this time). If you are using a USB to serial converter between the computer and the programming interface, this might cause the problem. I would try the adjustment recover and reprogramming the radio with the default file but ...
by rfcom
Sun Mar 15, 2009 9:58 am
Forum: Vertex
Topic: VX-924 "Channel Step Mismatch" error while programming
Replies: 6
Views: 2358

Re: VX-924 "Channel Step Mismatch" error while programming

It looks like the data (IF frequency) sent to the radio got corrupted.
You should be able to correct it by performing the Adjustment Recover under the Radio tab.

Michel