Search found 135 matches

by redbird
Tue Dec 06, 2016 5:26 pm
Forum: Kenwood Commercial Products
Topic: Kenwood date of manufacture
Replies: 0
Views: 1688

Kenwood date of manufacture

I have a TK-2402V-K. How can I tell by the serial B5C11469 how old it is? The battery code is U421F. How old is it?
by redbird
Fri Apr 29, 2016 4:10 pm
Forum: Vertex
Topic: Vxr-7000 Is this the correct Programming Cable
Replies: 3
Views: 1224

Re: Vxr-7000 Is this the correct Programming Cable

The specs on a VXR7000 are 150-174 MHz and 50 watts.
by redbird
Fri Apr 29, 2016 11:16 am
Forum: Vertex
Topic: Vxr-7000 Is this the correct Programming Cable
Replies: 3
Views: 1224

Re: Vxr-7000 Is this the correct Programming Cable

The internal duplexer will not work with .6 mHz spacing. Look at the physical size of such a duplexer.
I only use factory original programming cables. No ebay junk. Vertex calls for VPL-1 RJ-45 or CT-29/CT-126 serial cable.
FIF10A or FIF-12A/CT-104A USB cable.
by redbird
Sun Apr 10, 2016 3:38 pm
Forum: Vertex
Topic: VXR-1000 Jumper Defaults...
Replies: 1
Views: 326

Re: VXR-1000 Jumper Defaults...

Factory defaults:
JP06 towards side of board OUT. Towards center of board IN.
JP10 IN
JP11 towards front IN. Towards rear OUT.
JP12 OUT
JP13 IN
by redbird
Sat Jan 02, 2016 10:30 am
Forum: Vertex
Topic: VX-2100-DO-50 P1 & P2 program
Replies: 0
Views: 9463

VX-2100-DO-50 P1 & P2 program

I programmed a VX-2100 P1 for direct channel 1 and P2 for direct channel 2. Both buttons cause radio to go to channel 1. What is wrong?
by redbird
Sat Oct 31, 2015 5:01 pm
Forum: Icom Commercial Radios
Topic: IC-F5021 cloning cable
Replies: 1
Views: 4482

IC-F5021 cloning cable

F5021 uses a OPC-1122U USB cable. Can I use my OPC-1122 serial cable to program a F5021?
by redbird
Sun Sep 27, 2015 2:52 pm
Forum: Harris Public Safety Communications (PSPC) Equipment
Topic: two radios to one antenna question
Replies: 1
Views: 783

Re: two radios to one antenna question

Read about a Comet CF-416A duplexer. I have seen these used for two radios. Also get a dual band antenna like a Larsen.
by redbird
Sun May 17, 2015 4:45 pm
Forum: RELM/Regency/Wilson
Topic: sub audable tone
Replies: 3
Views: 4336

Re: sub audable tone

My manual is for RH256N with serial starting with 817-. The CTCSS tone dev is R358.
by redbird
Sat Nov 03, 2012 10:31 am
Forum: Icom Commercial Radios
Topic: IC-F121 clone mode ?
Replies: 1
Views: 1314

IC-F121 clone mode ?

I have a IC-F121 that I can not read, ever. I have another IC-F121 that I can read sometimes. I have the latest original software. Cable is UPC-1122. Software is CS-F100. My computer is XP. Error message is no power to radio, wrong port, cable problem. Is there a clone mode to get radio ready for re...
by redbird
Wed Jan 25, 2012 6:47 pm
Forum: Kenwood Commercial Products
Topic: TK-3200L
Replies: 0
Views: 1221

TK-3200L

I have a TK-3200L that always gives a voice announcement of channel number when switched on or changing channels. Sometimes it announces when just setting there. The radio also fails to power up when switched on sometimes. Can the voice announcements be programmed off with software? What causes the ...
by redbird
Sat Nov 12, 2011 10:58 am
Forum: Vertex
Topic: VX824 display board removal
Replies: 0
Views: 1712

VX824 display board removal

I need to remove the display board in a VX824. The board only has 4 screws instead of the six screws showned in the service manual. The top of the board has tabs that go into slots in the top of the case. The board does not want to lift out. I am afraid to pry up much. Is there anything else holding...
by redbird
Sat Apr 16, 2011 9:01 am
Forum: General Chatter
Topic: Bat Board
Replies: 5
Views: 3197

Bat Board

When is the Bat Board coming back up ?
by redbird
Wed Feb 23, 2011 10:03 am
Forum: Vertex
Topic: Vertex battery date codes
Replies: 0
Views: 2454

Vertex battery date codes

Anyone have a chart for decoding Vertex battery date codes like E33A ?
by redbird
Tue Nov 02, 2010 1:44 pm
Forum: Icom Commercial Radios
Topic: IC-F320-S-6 and Narrow Band
Replies: 2
Views: 3726

IC-F320-S-6 and Narrow Band

Will a IC-F320-S-6 program to narrow band?
by redbird
Tue Jul 27, 2010 5:27 pm
Forum: Kenwood Commercial Products
Topic: TK-3101 Squelch
Replies: 0
Views: 1136

TK-3101 Squelch

I have a TK-3101 with tight squelch. Is the squelch adjustment by software or a pot ? Any instructions will be helpful. Does anyone have a link to service manual ?